Specification

LED Edit Software Download Links:

Ledsoft-LedEdit 2013_V1.56.zip

Ledsoft-LedEdit 2014_V2.4.rar


t 1000s led controller - Controllers

1.T-1000S System features

1. 32—256 Gray level, Support software Gamma correction。
2. Support the rules and special-shaped handle.
3. Single-port output, can support 2048 pixels。
4. Off-line(SD Card) control, playback content stored in the SD card.
5.T-1000S stores a maximum of 16 programs, copy multiple files to the SD card in order,
after formatting the SD card as “FAT” format.
6. The program must be named in the order. just as: 00_1.led, 01_1.led, 02_1.led.
7. Compatible with a single line or double line chips.

NOTE:

1. When the T-1000S controller control less than 512 lamps the frame rate can reach 30fps. When the T-1000S controls more than 512 lamps and less than 2048 lamps the frame rate will slow down automatically.
2. T-1000S must use the new software LedEdit 2012.

2. Support chips:

t 1000s led controller 1 - Controllers

3. Appearance picture

t 1000s led controller 1 - Controllers

4. Definition of printing:

t 1000s led controller 2 - Controllers

NOTE: For the TTL(SPI) signal, the controller signal ground must connect to the LED ground directly.

5. Mode of connection

t 1000s led controller 2 - Controllers

1. Multiple T-1000S controllers can be cascaded together and work synchronously.
2. T-1000S one TTL(SPI) signal and one RS485 signal port output, can control 2048 pixels/lamps;
3. When the chip for LED is a single line chip just with data, then just needs to be connected with the DAT and GND of the
controller. If the chip for LED is a double line chip with DAT and CLK, then need to be connected with DAT, CLK, and
GND of the controller.
4. If you need to use RS485 signal you need to connect controller A interface with LED lamps A (DMX+), controller B
interface with LED lamps B(DMX-),
5. If you need to control a new IC type by the controller, the software code mode is the T-1000-IC model.

t 1000s led controller 3 - Controllers

6. Name of the program: (The rule of how to name the programs)

The name for NO.2 controller:
“00_1.led” ——— NO.1 program for No.1 controller
“01_1.led” ——— NO.2 program for No.1 controller
“02_1.led” ——— NO.3 program for No.1 controller
……
“15_1.led” ——— NO.16 program for No.1 controller
The name for NO.2 controller:
“00_2.led” ——— NO.1 program for No.2 controller
“01_2.led” ——— NO.2 program for No.2 controller
“02_2.led” ——— NO.3 program for No.2 controller
……
“15_2.led” ——— NO.4 program for No.2 controller
………
PIC:

t 1000s led controller 4 - Controllers

7. Special parameters

Memory card:
type: SD card(suggest using high-speed SD card)
Capacity: 128MB—2GB
Format: FAT
Store file: *.led
Physical parameters:
Working temperature: -30℃—85℃
Working voltage: DC5V / DC7.5-24V
Working power: 1W
size: L165mm×W80mm×H30mm
weight: 0.35KG
signal port: 3pin connect port

Note:
Before copy files to an SD card, The SD card must be formatted in FAT format

t 1000s led controller 5 - Controllers

The SD card in the controller can not be hot-swappable, plug the SD card every time, you must first disconnect the
power supply

7. Troubleshooting

Question 1: After power, the T-1000S ERROR indicator has been flashing without display output
Answer: The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:
①SD card is empty, with no effect file.
②The effect file in the SD card and the controller model do not match, please choose the correct controller model in LedEdit and then re-create the effect file *led.
③SD card did not format to FAT before copying effect files.
④Please check the supply power voltage, the controller can be individually powered to exclude power reasons
⑤Changing the SD card and then test to exclude the possibility of a bad SD card

Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change
Answer: The reasons for this are as follows:
① Check if the lighting′s signal line and the controller connected correctly
② If the TTL signal is received, the lamp and the controller must be common ground, that means connecting the lighting′s and the controller′s ground together
③ Check if the model was chosen during making display files on the SD card match the chips used in the lighting

LED Edit Software Download Links:

Ledsoft-LedEdit 2013_V1.56.zip

Ledsoft-LedEdit 2014_V2.4.rar