>
X
Home > Products > Controllers > T-8000A-TTL Controller For 6803 WS2801 WS2811 WS2812 WS2812B LED Strip

T-8000A-TTL Controller For 6803 WS2801 WS2811 WS2812 WS2812B LED Strip

  • Specification

1.T-8000A-TTL System Features

1. 32—256 Gray level,Support software Gamma correction。 2. Support the rules and special-shaped handle. 3. Eight--port output,every port can support 512-1024 pixels。 4. Off-line (SD Card) control, can be multiple controllers used in combination, play back content stored in the SD card. 5.T-8000A store a maximum of 16 programs,copy multiple files to the SD card in order,after formatting the SD card as “FAT” format. 6. The program must be named in orders ,just as :00_1.led, 01_1.led, 02_1.led. 7. Compatible with single and dual ICs, if you control a single line IC LED lights, without being connected to the CLK line. 8. New T-8000A have a screen, the controller can be encrypted to limit the times of use. NOTE: 1.When T-8000A controller control less than 512 lamps the frame rate can reach 30fps. When T-8000S controls more than 512 lamps and less than 1024 lamps the frame rate will slow down automatically.

2.Support chips:

3. Physical Picture

4. The meaning of flag

NOTE:For the TTL(SPI) signal, the controller signal ground must connect to the LED ground wire directly.

5. Mode of connection

6.File saving:

Rules for naming files(Use of multiple controllers at the same time) :

The name of the file on the first controller “00_1.led” ---------the first effect file “01_1.led” ---------the second effect file “02_1.led” ---------the third effect file …… “15_1.led” ---------the fifteenth effect file

The name of the file on the second controller “00_1.led” ---------the first effect file “01_1.led” ---------the second effect file “02_1.led” ---------the third effect file …… “15_1.led” ---------the fifteenth effect file

For example:

7. Specific parameters:

Memory cardtypeSD card(suggest using high-speed SD card) Capacity:128MB—2GB Format:FAT

Store file Format:*.led

Physical parameters: Working temperature :-30℃—85℃ Working voltage:DC5V Working power:3W Size:L200mm×W170mm×H50mm Weight:0.8KG Signal port:3pin connect port Demension:

NOTE:Before copy files to SD card ,The SD card must be formatted as FAT format. The SD card in controller can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply

8.Trouble shooting:

Question 1 :After power,the T-8000S ERROR indicator has been flashing without display output Answer:The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems: ①SD card is empty, with no effect file. ②The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led. ③SD card did not format to FAT before copy effect files. ④Please check the supply power voltage, the controller can be individually powered to exclude power reasons ⑤Changing the SD card and then test to exclude the possibility of a bad SD card

Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change Answer: The reasons for this are as follows: ① Check if the lamp′s signal line and the controller connected correctly ② If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lamp′s and the controller′s ground wire together ③ Check if the model chose during making display files on the SD card match the chips used in the lighting

Question 3:Controller and light connected, after. Lamps flicker. Controller indicator to normal. Answer:The reasons for this are as follows: ①The ground wire is not connected between the controller and lighting. ②The file in SD card is bad, Chip model does not match with the actual. ③Insufficient power supply.

Question 4:The SD card can not be formatted. Answer:The reasons for this are as follows: ①First make sure the SD card on the side of the protection switch is already open. ②SD card reader is broken ③Do all of this can’t deal with the question. Change the SD card tests again.

Contact Us :

We are looking forwarding to serving you.
Any questions please fill in the form below and we will reply to you within 12 hours, thank you!

*
*
*
Another Picture.
X